01 / 圆线01 / Round
圆线电磁线Round magnet wire
也就是最常见的漆包线、绕组线。所有复杂的特种线材,都是从这里开始的。MWS 生产全尺寸段圆线,配不同绝缘涂层覆盖各热等级。 The most common enamelled or winding wire — where every specialty construction begins. Produced across the full size range, with insulations for every thermal class.
产品概述Overview
圆线电磁线指圆形截面的单根绝缘导线,用于电机、变压器、继电器、音圈、传感器与电感绕组。它把电能与磁能相互转换——这也是「电磁线」这个名字的由来。 Round magnet wire is a single, circular-section insulated conductor used in motors, transformers, relays, voice coils, sensors and inductors. It converts electrical energy into magnetic energy — hence the name.
与普通铜线最大的区别在于那层薄薄的绝缘漆:没有它,绕组之间会短路,线圈就无法形成电磁铁。因此绝缘层的材料、厚度与均匀性,几乎决定了线圈的全部性能。 What separates it from plain copper is the thin insulation film. Without it, turns would short and the coil would stop acting as an electromagnet. Material, thickness and uniformity of that film define almost all coil performance.
绝缘结构Construction
大多数圆线采用多层涂覆结构:底漆直接附着铜面提供附着力和基础绝缘;中间层承担主要介电强度;面漆决定耐化学性、耐磨性与可焊性。层数越多,绝缘越厚,也越占空间。 Most round wires use a multi-coat structure: a base coat for adhesion and basic insulation, a middle coat carrying dielectric strength, and a topcoat deciding chemical resistance, abrasion resistance and solderability. More coats mean thicker insulation and less copper in the same slot.
绝缘厚度等级(Build)Build
- Single单层标准厚度,槽满率最高,用于常规绕组Standard single build — highest fill, general windings
- Heavy加厚绝缘,耐久性与耐压更好,适合绕线张力较大的场合Thicker insulation for endurance and voltage, where winding tension is high
- Triple三层加强,用于高压或严苛机械应力环境Three builds for high voltage or harsh mechanical stress
- Quad最厚,常用于逆变器驱动电机与高可靠性场景Thickest — inverter-duty motors and high-reliability applications
选择 build 时不要只看耐压。绝缘越厚,同一槽内可容纳的铜就越少,铜耗与温升随之上升。这是一次典型的「耐压 vs 效率」权衡。 Don't choose build on voltage alone. Thicker insulation means less copper in the slot, which raises copper loss and temperature rise. It's a classic voltage-versus-efficiency trade.
热等级与产品代号Classes & product codes
热等级是选型的第一道门槛。下表为常用体系;方线与矩形线另遵循 NEMA MW 18 / MW 20 等独立条目。 Thermal class is the first gate. Common systems below; square and rectangular wire follow separate NEMA entries such as MW 18 and MW 20.
| 热等级Class | 绝缘体系Insulation | MWS 代号MWS code | NEMA | IEC 60317 | 可焊性Solderable |
|---|---|---|---|---|---|
| 105 °C | Plain Enamel | PEN | — | — | 否No |
| 105 °C | Formvar | FMW 15 | MW 15 | 60317-1 | 否No |
| 155 °C | Polyurethane | P155 | MW 79 | 60317-20 | 是Yes |
| 155 °C | Polyurethane Nylon | PN155 | MW 80 | 60317-21 | 是Yes |
| 180 °C | Polyurethane | P180 | MW 83 | 60317-51 | 是Yes |
| 180 °C | Polyurethane Nylon | PN180 | MW 83 | 60317-55 | 是Yes |
| 180 °C | Polyester-imide | PT | MW 30 | 60317-8 | 否No |
| 180 °C | Solderable Polyester | SPT | MW 77 | 60317-23 | 是Yes |
| 200 °C | Polyester A/I Topcoat | APT | MW 35 | 60317-13 | 否No |
| 240 °C | Polyimide | ML | MW 16 | 60317-43 | 否No |
「可焊性」指能否在不机械剥漆的情况下直接锡焊。聚氨酯类(P/PN)在 370°C 左右可直接焊接,是高密度端子与音圈绕组的常见选择。 "Solderable" means the wire can be soldered without mechanical stripping. Polyurethane types (P/PN) solder directly around 370°C — common for dense terminals and voice coils.
尺寸与电阻参考Sizes & resistance
下表为裸铜导体的标称值(20°C)。实际成品外径需加上绝缘层厚度,依 build 不同而变化,请在最终设计时以规格书为准。 Nominal bare-copper values at 20°C. Finished outer diameter adds insulation per build — confirm against the datasheet before final design.
| AWG | 标称直径 (mm)Nominal dia. (mm) | 截面积 (mm²)Area (mm²) | 直流电阻 (Ω/m)DC resistance (Ω/m) | 常见用途Typical use |
|---|---|---|---|---|
| 10 | 2.588 | 5.261 | 0.00328 | 大功率电机、变压器Power motors, transformers |
| 14 | 1.628 | 2.081 | 0.00828 | 电机主绕组Main motor windings |
| 18 | 1.024 | 0.823 | 0.0209 | 继电器、电感Relays, inductors |
| 22 | 0.6438 | 0.325 | 0.0530 | 小型变压器Small transformers |
| 26 | 0.4049 | 0.129 | 0.134 | 拾音器、传感线圈Pickups, sensor coils |
| 30 | 0.2546 | 0.0509 | 0.339 | 高频电感、音频HF inductors, audio |
| 34 | 0.1601 | 0.0201 | 0.857 | 耳机音圈Headphone coils |
| 38 | 0.1007 | 0.00797 | 2.16 | 微电机、医疗Micro motors, medical |
| 44 | 0.0503 | 0.00199 | 8.67 | 超微细互连Ultra-fine interconnects |
需要其他线径?我们的库存包含半号规格(如 23.5 AWG),可用 AWG 选型工具 自行估算电阻与重量。 Need another gauge? Stock includes half sizes (e.g. 23.5 AWG). Use the AWG calculator to estimate resistance and weight.
选型建议Selection guidance
- 工作温度Operating temp.先确认长期工作温度,再上浮 20°C 余量选热等级Fix the continuous temperature, then add ~20°C margin to pick the class
- 是否锡焊Soldering需要免剥漆直焊 → 选 P / PN / SPT 体系Direct solder without stripping → P / PN / SPT families
- 浸漆与封装Varnish / potting确认绝缘层与漆、树脂的化学兼容性Check chemical compatibility with varnish and resin
- 绕线张力Winding tension张力大、层数多 → 提高 build 等级High tension, many layers → step up the build
- 槽满率Fill factor空间受限可考虑 Microsquare® 或异形线Space-constrained? Consider Microsquare® or shaped wire
常见误区:把 200°C 等级当作「更保险」的默认选择。更高等级往往意味着更难焊接、更难浸漆、成本更高。合适的才是最好的。 Common mistake: defaulting to 200°C "for safety." Higher classes are usually harder to solder, harder to varnish and more expensive. The right class beats the highest class.
常见问题Frequently asked questions
圆线电磁线的规格范围是多少?What range does round magnet wire cover?
望溪供应的 MWS 圆线覆盖 AWG 4–50,热等级 105–240 °C,绝缘厚度从 Single 到 Quad,起订量低至单盘。MWS round wire runs from AWG 4 to 50, thermal classes 105–240 °C, builds Single to Quad, with MOQ down to a single spool.
Single、Heavy、Triple、Quad 怎么选?How do I choose between Single, Heavy, Triple and Quad?
本质是耐压与槽满率的权衡:Single 槽满率最高;Heavy 与 Triple 适合绕线张力大或高压场合;Quad 常见于逆变器驱动电机。绝缘越厚,同槽铜量越少,铜耗与温升随之上升。It is a trade between voltage withstand and fill factor. Single gives the highest fill; Heavy and Triple suit high tension or higher voltage; Quad is common in inverter-duty motors. Thicker builds leave less copper in the slot, raising losses and temperature rise.
哪些型号可以不剥漆直接焊接?Which types solder without stripping?
聚氨酯类 P155 / PN155、P180 / PN180 在约 370 °C 可直接锡焊,适合高密度端子与音圈绕组;聚酯与聚酰亚胺(PT、APT、ML)需要机械或化学剥漆。Polyurethane types P155/PN155 and P180/PN180 solder directly around 370 °C — common for dense terminals and voice coils. Polyester and polyimide types (PT, APT, ML) need mechanical or chemical stripping.
交期与起订量?Lead time and MOQ?
标准规格库存充足,常见型号 6–8 周内到货;规格确认与库存查询 48 小时内回应。Standard specs are well stocked; common models arrive in 6–8 weeks. Spec confirmation and stock checks within 48 hours.
有半号规格的现货吗?Is half-size stock available?
常见半号(half-size)规格有库存,覆盖中小线径段的常用热等级;非标热等级或特殊 build 按原厂排产,常见型号 6–8 周内到货。Common half-size specs are stocked across the mid and fine gauge range and usual thermal classes. Non-standard classes or builds are scheduled at the factory, typically arriving in 6–8 weeks.
还有其他问题?把规格发给我们,48 小时内回复。Still have questions? Send us your spec — we reply within 48 hours.