首页Home/ MWS wire/ 异形线Shaped magnet wire

02 / 异形线02 / Shaped

异形线Shaped magnet wire

矩形线、带状扁线与方线。当线材截面形状直接决定线圈功能与设计时使用——尤其在高槽满率、短端部与散热要求严格的场合。 Rectangular, ribbon and square magnet wire — for coils where conductor geometry is critical to function, fill factor and heat path.

RECT · RIBBON · SQUARE
0.10 – 6.0 mm

产品概述Overview

矩形线、带状扁线与方线统称异形电磁线。当线材截面形状直接决定线圈功能与设计时使用——尤其在需要高槽满率、短端部或良好散热的场合。 Rectangular, ribbon/flat and square wire together make up shaped magnet wire. Used where conductor geometry is critical to coil function — especially for high fill factor, short end turns and good heat paths.

相比同截面积的圆线,异形线能把槽内空隙压到最小。绕组的铜占比提升,意味着同样的槽面积可以输出更大扭矩,或同样的输出需要更少的铜。 For the same cross-section, shaped wire minimises the gaps between turns. More copper per slot means more torque from the same slot area — or less copper for the same output.

截面形状Profiles
Rect / Ribbon / Square
厚度范围Thickness
0.10 – 6.0 mm
宽厚比Aspect ratio
1 : 1 – 1 : 30
典型行业Markets
EV · 变压器
Shaped wire profiles
异形截面与圆线截面在槽内的填充差异(示意)Fill comparison between shaped and round sections (illustrative)

常见截面Common profiles

类型Type 特征Feature 典型应用Typical use
矩形 Rectangular四角带圆角,宽厚比可控Rounded corners, controllable ratio驱动电机定子、变压器Traction stators, transformers
扁带 Ribbon / Flat极薄且宽,可绕成扁线圈Very thin and wide, for flat coils无线充电、扁平电感Wireless charging, flat inductors
方线 Square等边截面,绕制方向无关Equal sides, orientation-agnostic小型电机、继电器Small motors, relays

异形线的关键是圆角半径。半径过小会在折弯时产生应力集中,导致绝缘层开裂;半径过大则牺牲填充效率。我们按你的绕线工艺推荐合适的圆角。 Corner radius is the crux. Too tight and bending stress cracks the insulation; too generous and you lose fill. We recommend a radius matched to your winding process.

选型与定制Selection & custom

  • 宽厚比宽厚比过大时绕线易翻倒,需评估导向工装Very high aspect ratios can roll during winding — evaluate guides
  • 绝缘体系矩形线遵循 NEMA MW 18 / MW 20,热等级同圆线体系Rectangular wire follows NEMA MW 18 / MW 20 with the same thermal classes
  • 端部处理矩形线端部通常需激光剥离或专用剥漆Ends usually need laser ablation or dedicated stripping
  • 最小批量异形线多为定制拉制,起订量高于圆线Shaped wire is usually custom drawn, with higher MOQ than round

如果你的初衷只是「想让槽满率更高一点」,先算一下换成异形线的收益是否覆盖定制的模具与起订成本。If the goal is simply a bit more fill, check whether shaped wire's gain covers the tooling and MOQ cost.

常见问题Frequently asked questions

异形线可以做哪些截面?Which profiles are available?

矩形、带状与方形截面,厚度 0.10–6.0 mm,宽厚比 1:1 至 1:30,可按图纸定制。Rectangular, ribbon and square sections, 0.10–6.0 mm thick, aspect ratios from 1:1 to 1:30, made to drawing.

为什么用异形线而不是圆线?Why use shaped wire instead of round wire?

同占用面积下槽满率更高、散热路径更短、绕组体积更小,常见于电动汽车驱动电机与油浸式变压器。Higher fill factor in the same space, shorter thermal paths and smaller winding volume — common in EV traction motors and oil-immersed transformers.

定制截面需要提供什么?What is needed for a custom profile?

截面尺寸、圆角、宽厚比与公差要求;我们先做规格确认,再给模具与批量方案。Section dimensions, corner radii, aspect ratio and tolerances. We confirm the spec first, then quote tooling and volume.

扁线电机(hairpin)该怎么选扁线?How do I choose flat wire for a hairpin motor?

先定槽形:按槽宽槽深排布导体数,反推单根扁线的厚度与宽度;再定宽厚比(常见 1:2–1:6)与圆角半径,最后按 800 V 平台选耐电晕绝缘与热等级。槽满率每提升 1 个点,铜耗与温升都会跟着变,宁可在规格确认阶段多算一轮。Start from the slot: lay out the conductor count against slot width and depth to derive thickness and width, then fix the aspect ratio (typically 1:2 to 1:6) and corner radius, and finally pick corona-resistant insulation and thermal class for an 800 V platform. Every point of fill factor moves copper loss and temperature rise.

还有其他问题?把规格发给我们,48 小时内回复。Still have questions? Send us your spec — we reply within 48 hours.

询价与技术支持Quote & support

把规格发给我们。Send us the spec.

上海团队提供中文技术对接与等效替代建议;标准规格库存充足,常见型号 6–8 周内到货。Our Shanghai team handles Chinese-language support and cross-referencing; standard specs are well stocked, common models arrive in 6–8 weeks.

获取报价Request a quote→